Metal Cage
The cage retains the nut and controls its permitted movement. Its outer dimensions, spring features, retaining tabs, and panel engagement structure depend on the mounting design.
Discover our comprehensive range of high-precision fasteners, stampings, and machined components. Manufactured under strict IATF 16949 quality standards.
Floating Cage Nuts with Nylon Washers are captive fastening assemblies designed to provide a threaded connection in sheet metal structures while allowing limited lateral movement for alignment. The cage holds the nut in position while permitting it to float within a defined range, helping compensate for minor differences between mating holes during assembly. A nylon washer can be incorporated into the assembly to provide a non-metallic contact surface and support the specified installation requirements.
These fasteners are used in automotive panels, equipment enclosures, electrical cabinets, and other sheet metal assemblies where access to the rear side of a mounting point is limited or where component alignment requires some adjustment. Cage dimensions, nut thread, floating clearance, washer material, and retention structure should be specified according to the application and assembly conditions.
The cage is mounted or retained in a prepared panel opening, keeping the nut captive at the designated fastening position. Unlike a fixed nut, the internal nut can move slightly within the cage boundaries. This floating action helps the bolt engage when the mating component and panel holes are not perfectly aligned.
The nylon washer is positioned according to the assembly design. Depending on its location and geometry, it may provide a separating or contact surface between components. Its material grade and dimensions should be selected based on temperature, load, chemical exposure, and the required service conditions.
The cage keeps the nut associated with the panel or mounting position.
The floating clearance allows adjustment during bolt engagement.
The washer provides a specified non-metallic interface within the assembly.
The cage retains the nut and controls its permitted movement. Its outer dimensions, spring features, retaining tabs, and panel engagement structure depend on the mounting design.
The nut provides the internal thread for bolt installation. Thread diameter, pitch, tolerance, nut dimensions, and material are specified according to the required connection.
The washer adds a polymer contact element to the assembly. Its thickness, inner diameter, outer diameter, and nylon grade should be matched to the intended use.
Selection should focus on how the cage, nut, and washer work together in the actual panel and fastening configuration.
Floating movement can help accommodate limited positional variation between mating components, subject to the available clearance and cage design.
The cage holds the threaded nut at the mounting location, reducing the need to position a separate loose nut during installation.
The nylon washer provides a polymer surface where the design requires separation or contact control. Its suitability depends on load, temperature, and environmental exposure.
Cage geometry can be developed around panel thickness, opening dimensions, access conditions, and the required retention method.
Can be specified for selected vehicle panel assemblies, brackets, mounting structures, and interior component connections where captive threaded points are required.
Used in sheet metal enclosures, control cabinets, and equipment housings to provide threaded attachment points for covers, brackets, and internal components.
Suitable for selected machine panels, access covers, support plates, and fabricated equipment structures that require captive fastening hardware.
Can be incorporated into sheet metal housings and fabricated assemblies where installation access or hole alignment needs to be considered.
Exact specifications depend on the customer's drawing, mating panel, bolt selection, and operating environment. The following items form a practical basis for technical confirmation.
| Specification | Details to Confirm |
|---|---|
| Assembly Type | Floating cage nut with nylon washer |
| Thread | Metric or other specified thread standard, diameter, and pitch |
| Nut Material | Steel or other specified material according to application requirements |
| Cage Material | Specified steel grade and required mechanical characteristics |
| Washer Material | Nylon grade selected according to temperature, load, and environmental conditions |
| Floating Range | Required lateral movement and allowable alignment compensation |
| Panel Compatibility | Panel thickness, opening dimensions, and retaining structure |
| Surface Treatment | Specified coating or finish for the metal components |
| Inspection Requirements | Thread fit, dimensional tolerances, retention, washer condition, and agreed criteria |
A cage nut assembly should be evaluated as a complete fastening unit rather than by thread size alone. The panel opening, cage retention, available floating movement, washer position, and bolt engagement all influence whether the component fits the intended assembly.
Match the nut thread with the mating bolt and required engagement length.
Confirm panel thickness, hole geometry, and cage retention dimensions.
Specify the movement needed to accommodate the assembly's positional tolerance.
Review washer dimensions, material grade, operating temperature, and chemical exposure.
Different panel structures and assembly conditions may require variations in cage geometry, nut dimensions, thread specifications, and washer configuration. Custom production can be arranged according to technical drawings, samples, or agreed specifications.
OEM and ODM cooperation is available for projects that require application-specific development, dimensional adjustment, or repeat supply. Before production, the mounting panel, mating bolt, required floating range, and washer function should be reviewed together.
Check cage dimensions, nut geometry, thread position, washer dimensions, and other drawing-defined features.
Verify the thread specification and confirm that the mating fastener can engage as required.
Check that the nut moves within the specified range without becoming detached from the cage.
Inspect the nylon washer for damage or deformation and review the metal finish against the agreed requirements.
To evaluate a floating cage nut assembly accurately, buyers should provide as much of the following information as possible:
A floating cage nut provides a captive threaded connection while allowing limited lateral movement of the nut. This movement helps accommodate minor positional differences between mating holes during assembly.
A nylon washer provides a non-metallic contact surface within the fastening assembly. Its specific function depends on its position and design, and may include separation or contact control. The required material grade should be selected according to operating conditions.
Yes. The permitted movement can be specified through the cage and nut geometry. Buyers should provide the required alignment allowance or the relevant panel and mating-hole dimensions.
They can be used in suitable automotive sheet metal and component assemblies. Selection should account for panel thickness, thread requirements, retention, vibration conditions, environmental exposure, and the applicable validation standards.
Thread sizes and washer dimensions can be discussed according to the product drawing or sample. The cage, nut, and washer should be evaluated together to confirm dimensional and functional compatibility.
A drawing or sample is the most useful starting point. Include thread details, cage dimensions, panel thickness, floating range, washer requirements, material, surface treatment, and estimated order quantity.
Zhejiang Xinye Automobile Technology Co., Ltd. traces its business origins to 1995 and specializes in the research, development, and manufacturing of automotive fasteners and metal stamping components. We are China Floating Cage Nuts with Nylon Washers Manufacturers and Custom Floating Cage Nuts with Nylon Washers Suppliers & Factory.
Our engineering focus covers fastening reliability, dimensional accuracy, mechanical performance, corrosion protection, and application-specific component development.
Deep application knowledge, in-house manufacturing, and certified quality management, applied to the most demanding automotive requirements.
Our business traces its origins to 1995, with more than 30 years of experience in automotive fasteners and stamping parts. This long-term focus builds application knowledge in flange nuts, weld nuts, specialty fasteners, and related metal components.
Standard and non-standard nuts, weld nuts, self-locking nuts, knurled nuts, clinch nuts, sliding nuts, bolts and screws, metal stampings, CNC-machined sleeves and pins, and specialty automotive components.
Production is completed in-house from raw materials to finished goods, using automatic cold heading machines, tapping machines, heat-treatment lines, thread-rolling equipment, and hardness testing.
More than 30 years of R&D experience in strength grades, tolerance accuracy, corrosion resistance, temperature performance, and MAT self-correcting thread technology.
We develop Class 12 nuts and carry out pre-research on Class 13 to 14 ultra-high-strength nuts for higher axial-load requirements, such as heavy-duty trucks and high-performance engines.
Tolerance control ranges from 0.06 to 0.30 mm for different applications, with a strong emphasis on thread-fit precision. Final tolerances are defined by product drawings and inspection reports.
Trivalent zinc plating with a stated 480-hour salt-spray result, and Zn-Ni alloy plating with stated results of 480 to 720 hours. Temperature-resistance options of 300, 550, and 650 to 700 degrees Celsius for selected applications.
The MAT thread nut features a self-correcting function on the first few threads, guiding a slightly misaligned bolt into the correct thread path during automated assembly.
Certified to IATF 16949:2016. The quality system covers raw material intake, process inspection, and finished-product testing, including tensile, CMM dimensional, pull-off, fusion-depth, destructive weld, and salt-spray tests.
Drawing and sample review, material and process recommendations, sample trials, dimensional and performance validation, cost optimization, order tracking, batch traceability, logistics coordination, and after-sales technical support.
In-house production and testing capabilities that support process consistency and product conformity.
Production
Automatic cold heading machines, tapping machines, heat-treatment lines, thread-rolling equipment, and hardness testing support production from raw materials to finished goods.
Inspection
Inspection capabilities include tensile, CMM dimensional, pull-off, fusion-depth, destructive weld, and salt-spray tests across raw material intake, process inspection, and finished-product testing.
Technical highlights that matter when specifying automotive fastening components.
These figures are company-reported. Actual tolerances and performance results should be confirmed against product drawings and inspection reports.
| Metric | Company Information |
|---|---|
| Business origin | 1995 |
| Industry experience | More than 30 years |
| Product varieties | More than 500 |
| Quality certification | IATF 16949:2016 |
| Reported tolerance range | 0.06 to 0.30 mm, depending on application |
| Trivalent zinc plating | 480-hour salt-spray result stated |
| Zn-Ni alloy plating | 480 to 720-hour salt-spray result stated |
| Temperature resistance options | 300, 550, and 650 to 700 degrees Celsius for selected applications |
| High-strength nut development | Class 12 development; Class 13 to 14 pre-research |
Automotive fastening and functional components, supported by a broader manufacturing range of nuts, bolts, screws, metal stampings, CNC-machined sleeves, pins, and shafts.
Product suitability is assessed against customer drawings, material grade, strength class, thread specification, tolerance, surface treatment, temperature exposure, corrosion requirements, and assembly method.
Trusted by B2B buyers who need dependable fastening and metal components built to drawing.